Recent Posts

Pages: [1] 2 3 ... 10
1
Cube 3D printer discussion / cube not connected
« Last post by amber915@myncsd.org on May 01, 2019, 12:37:47 pm »
One more issue
"Cube is not connected.  Please click on link cube first to connect to the cube"
there is no message on printer to do the link
have to totally disconnect power source to go back to home screen
2
Cube 3D printer discussion / download software for mac
« Last post by amber915@myncsd.org on May 01, 2019, 12:12:50 pm »
I am trying to download Cube 3d printer 2nd generation for Mac using a link that 3D systems gave me.  The link is invalid.
Also, USB connection from a windows machine to cube is not recognized.
Downloaded a project to flash drive - cube does not recognize it.
I am new to using the printer, but our organization has had it since 2014 but the person using it before has left.  Having all kinds of other issues and was wondering if anyone out there could be my "Cube buddy" to help me out with some issues.
Any help would be appreciated,  Thanks
af
this is the link I was given for Mac software
https://3dsystems.sharefile.com/d-sf50faa3bac14566b
3
Cube 3D printer discussion / Re: FrankenCube v0.1 Its ALIVE!!!
« Last post by ShadowedR on April 02, 2018, 10:07:48 am »
After some testing a realised a few mistakes in my design and promptly fixed it.
Here is a new version:  https://www.thingiverse.com/thing:2839509

4
Cube 3D printer discussion / Re: FrankenCube v0.1 Its ALIVE!!!
« Last post by ShadowedR on March 25, 2018, 11:23:48 am »
For those interested, I finished making and replacing the stock extruder on my cube with an E3D V6.
All in all I can max out Z at 133, so I lost a few mm, but it works great.



Check it out here:
https://www.thingiverse.com/thing:2839509
5
Cube 3D printer discussion / Unblocker for Cube .... www.cubesaver3d.com
« Last post by ROBERTO GEHLEN OLIVEIRA on September 01, 2017, 04:50:52 pm »
Unblocker for Cube 1 & 2 available  on www.cubesaver3d.com
6
Cube 3D printer discussion / Re: FrankenCube v0.1 Its ALIVE!!!
« Last post by chandto on May 17, 2017, 08:54:51 pm »
Congrats on jail breaking and opensourcing the cubex printers.  I'm a disappointed owner of a stock cubex duo and am beginning the journey of converting my printer.  I was wondering if anyone has documented the items needed and steps to perform to get the conversion done.  I would greatly appreciate any documentation that exists or any help for that matter. 

Thanks all for any advice and assistance, I haven't had a chance to read the entire thread so if I've missed what I'm looking for, please just let me know and I'll go back and find it.

Regards,
Charles
7
All information posted by Prof2meca is false, he is trying to difame me ... he's a criminal
8
Cube 3D printer discussion / Re: CUBE3DFREE is a fake
« Last post by ROBERTO GEHLEN OLIVEIRA on April 07, 2017, 10:52:16 am »
This comment is false, this guy is posting false information on the net to difame me
9
Cube 3D printer discussion / Re: FrankenCube v0.1 Its ALIVE!!!
« Last post by gcurtis79 on March 30, 2017, 02:34:38 am »
I Frankencubed mine as well, with excelent results. I used a dremmel to cut off the portion of the original board with the power/usb/fuse and used it in place to keep things looking nice. I did the same with the portion that had the USB port, as both had nice screw mounts to utilize for this.

I used every stock part, including extruder/hot-end, only replacing the control board with an MKS-BASE 1.0.

The fans had 12v regulators on them already, so running on the original 24v power supply was not a problem. Just make sure you observe and/or test the wires prior to powering them, or you'll blow up the regulators with reverse voltage. (I'll need to replace my cooling fan regulator because I did this.)

I set the stepper drivers with a multimeter on ground, and while touching the positive lead to the driver adjustment screw, I set them all to 2v (I think, I used an analogue multimeter, and I'm not sure if I was reading the scale properly), this made the motors run much quieter, and they don't get too hot.

I used Z-MAX since the limit switch is at the bottom, but MIN plug for both X and Y.

I'm currently using up the remainder of the spool of 1.6mm green it came with, but it will accept 1.75mm filament as well, you just have to remember to change the setting in your slicer.

The original screen is disabled currently and in place only for asthetics, but I plan on getting the 2.8 inch MKS-TFT and possibly the WiFi module, unless I find room for an Octo-Pi.  So far I enjoy that it still looks so clean.

Below you'll find my Marlin v1.1.0 RC8 Configuration.h, Slic3r config export, and CuraEngine config export. I've done a couple test prints with slicer, and a 'parts fit' test with cura, and the parts slid together whith little to no effort.

Edits for spelling and info aditions. Photos to come.
10
Cube 3D printer discussion / Re: Crap hack. Bulk filament
« Last post by pugiyac on March 18, 2017, 10:02:27 am »
Hi i just want to share the way i used in order to be able using 1.75mm bulk filament:
Before that every second print i had to tighten the screw that holds the stepper counter - after
doing those steps i had more that 70-80 hours of printing without any problem..

I disassembled the print head cover and released  fan+ light sensor screws.
took out the pulley (black and white circle) and grind small amount of metal from it (see pic 1).
then i noticed the pulley has a small bulge on the back side which fits exactly to it place every time you tight the nut back.
Therefore, every time you will tighten the screw to the pulley will be aligned to factory setting and not to 1.75m - and that we don't want !
so, i grinded the hole  that which the bulge fits into (the socket on the chase of the print head) then i had free space  to determine how
the pulley will be.

Now everything working just right, without any need to tight the bolts.  8)

P.s
you don't need an expensive device to hack your cube printer in order to use bulk filament (read the first post).
Just use "Crap hack" steps easy. the guy that sales those chips should consider lower to price.
paying for the "hack device" more then 15$ is a really bad joke..
Pages: [1] 2 3 ... 10